Point Dume Leaf 04 of 06

Point Dume · Ice makers

Water in the tray, nothing in the bin

You hear the fill, perhaps a hum afterward, and still the bin stays empty. That particular pattern narrows the fault more than most owners expect. Begin with the quick checks below; nearly all of them need no tools whatsoever.

4.8/5 from 187 client reviews How the rating is counted

Checks to make before phoning

Each one eliminates an everyday cause of an idle ice maker.

  • The ice maker is switched on, either at the control panel or with the switch on the unit itself; it gets turned off during cleaning more often than anyone admits
  • The bin is pushed fully home and sits square; a bin resting slightly forward can pause production
  • The shut-off arm or sensor lever is down, not stuck in the raised position by a stray cube or a frozen clump
  • Nothing stored in the freezer leans on the arm or crowds the chute
  • The freezer is genuinely cold: ice cream firm, packages hard to the touch
  • The supply valve, whether below the sink or behind the cabinetry, is open, and the line has not kinked after a recent move or remodel
  • Where a water filter is fitted, it has been swapped as the Sub-Zero guide describes

Who repairs Sub-Zero ice makers on Point Dume?

Malibu Sub-Zero Service fixes ice makers fitted inside Sub-Zero freezers, plus the freestanding undercounter ice machines tucked into kitchens and bars across the point and Malibu. Phones pick up 24/7. Sending a technician costs $89; approve a fix and those dollars come back off its invoice, which gets written only after diagnosis.

Water arrives, ice doesn't: what the pattern says

Water fills the tray, freezes into a slab, and the slab never leaves
The ejector motor or its thermostat is not finishing the harvest, or a sluggish freezer cannot turn the water solid on schedule
Cubes form in the tray but never drop into the bin
A harvest heater or ejector fault, or a shut-off arm that thinks the bin is already full
Small, hollow or misshapen cubes
Low water pressure, a partly clogged filter, or a fill valve passing too little water Repair page
Water leaking under the freezer or freezing as a sheet below the ice maker
A leaky inlet valve that keeps dribbling, a split fill tube, or a tray running over its edge
Cubes fusing into a block inside the bin
A bin left untouched for a long stretch, or a freezer that warms and refreezes; the refrigerator side may be struggling as well Repair page
Output falls behind during a party
Normal behavior: production is steady and fixed, so a crowd drains the bin quicker than new cubes can replace them Read the note

What the headland adds to the problem

An ice maker relies on three things that a house on the point can be hard on: a steady water supply, a cold freezer and a dry mechanism. Plenty of homes here have whole-house filters, softeners or other treatment added during remodels. When one of those clogs, or a valve upstream is left half closed, the ice maker still fills, just not enough to form full cubes. A pressure problem upstream looks exactly like an ice maker fault from the kitchen.

Freezer temperature is the second piece. In a kitchen that spends its afternoons open to the deck, a freezer working against warm, damp air may keep food frozen yet run too warm for the ice maker to complete its cycle in time. The result resembles a broken ice maker when the real trouble is a coil, a fan or a seal. For that reason the visit always includes the freezer, and it can make sense to have the refrigerator side examined at the same moment.

The third piece is moisture. Humid air that gets past a gasket can freeze on the shut-off arm or the chute and lock them in place. Melting that ice frees the arm for a while, but it comes back until that leak is sealed. A freestanding undercounter ice unit beside a pool or outdoor bar sees salt and sun on top of all this, which our undercounter page for the point discusses. General ice maker diagnosis is laid out on Sub-Zero ice maker repair; houses right on the sand get their own notes on the Broad Beach ice maker page; for the wider neighborhood, open our Point Dume overview.

Why does my Sub-Zero ice maker fill with water but make no ice?

Usually the freezer is too warm to freeze the tray in time, the shut-off arm is stuck up, or the ejector or harvest heater is failing so frozen cubes never leave the tray. Check the arm and the freezer first; when both look right, the ice maker module itself needs testing.

Ice-maker myths worth dropping

  • ForNo ice means the water valve has failed.

    ReadIf you can hear water entering the tray, the valve is opening. The fault more often lies in freezing or ejecting the ice: freezer temperature, the ejector, the harvest heater or the shut-off arm. Replacing the valve first is a common and avoidable expense.

  • ForAny noise during the fill means a bad ice maker.

    ReadA short fill with a buzz or hiss is ordinary. A long, loud fill, or banging in the pipes when the valve shuts, points to water pressure or the valve rather than to the ice maker.

  • ForThe first ice after a new filter is fine to use.

    ReadThose early batches can trap air or carry loose filter particles, and many guides advise discarding them. Check the Sub-Zero use-and-care guide for your model.

Freeing a stuck shut-off arm safely

  1. Switch the ice maker off

    Use the switch or the control panel so the mechanism cannot cycle while your hand is near it.

  2. Look before you pull

    Find what holds the arm up: a cube wedged beneath it, a frozen lump in the bin, or frost on the pivot.

  3. Melt it, never pry it

    Lift out the bin and soften small bits of ice with a warm, damp cloth. Skip the knife and do not lever the arm; it and its pivot are plastic and snap easily.

  4. Reseat the bin

    Slide it fully back into place and lower the arm to its working position.

  5. Turn it back on and be patient

    Production restarts slowly. If no cubes have dropped by the following day while the freezer stays cold, book a visit or call (310) 742-8625.

How do I fix a stuck Sub-Zero ice maker arm?

Switch the ice maker off, take out the bin and look for a cube or frost holding the arm up. Melt it free with a warm, damp cloth rather than prying, reseat the bin and lower the arm. If it sticks again soon, damp air is getting in or the mechanism needs service.

Ice-maker questions owners ask

How long before a Sub-Zero ice maker starts producing ice?
After installation or a reset it takes a while, often longer than people expect, because the freezer must be fully cold first. Your Sub-Zero guide gives the figure for your model. Cold freezer, empty bin the next day? Time to call.
Is the freezer still usable while its ice maker is out?
Certainly, provided the compartment stays properly frozen. Power the ice maker down if water escapes or the tray overfills, and shut the supply valve when you spot a leak.
What about freestanding undercounter ice machines?
Those are part of the work too. If yours lives outside near a pool or bar, say so while booking, so nobody hunts for it in the kitchen.
Does the freezer get inspected as well?
Always. An ice maker cannot work inside a warm freezer, so the freezer is part of every ice maker visit. Since $89 pays for the trip rather than one appliance, the refrigerator and other Sub-Zero units can be opened during that same stop.
What will the ice maker repair cost?
Getting someone out is $89, deducted later if you proceed. What the fix itself costs hinges on which component failed and how much labor it takes; that number is shared after inspection, before a single part changes.

Calls taken 24/7

Empty bin? Tell us what you hear.

Say whether water fills and whether ice forms in the tray; it saves time once the technician arrives. That $89 stop can include each Sub-Zero you own.

$89 covers the trip, not each appliance; it is then knocked off the invoice when you green-light the repair.