Pacific Palisades Leaf 04 of 06
Pacific Palisades · Ice makers
The plumber left, and the ice stopped
Repiping a kitchen, swapping a pressure regulator, replacing a shutoff under the sink: any job that drains the water lines can leave a Sub-Zero ice maker sulking afterward. Often the cause is a valve left closed or a pocket of air, and you can sort it out with a glance and a little patience. Other times the job knocked something loose inside the appliance, and that part is ours.
4.8/5 from 187 client reviews How the rating is counted
- Book a visit
- (310) 742-8625
- $89 per visit · out 8–6 daily · phone 24/7
Who can fix a Sub-Zero ice maker in Pacific Palisades?
Malibu Sub-Zero Service handles both kinds found in local kitchens: the icemaker built into a Sub-Zero freezer and the separate undercounter ice unit. The phone is answered 24/7 and visits are booked daily from 8 AM till 6 PM. Say yes to the repair and the $89 visit charge comes off it; its price is named once the cause has been found.
Post-plumbing tick list
Run down these lines before phoning anyone. More often than not, ice that vanished after pipe work is explained by one of them.
- The little branch valve for the fridge line is turned all the way open, not left at a quarter turn
- The main house shutoff and any valve under the sink were turned back on
- The supply hose behind or beside the unit is not kinked where the cabinet was pushed back
- A new water filter is seated and locked, if one was changed at the same time
- Nobody switched ice production off on the control panel while working nearby
- The arm or sensor that stops production is not stuck in the raised, full position
- No drip or damp patch under the refrigerator or in the cabinet next to it
- If the job touched the pressure regulator, the plumber confirmed normal pressure afterward
Why did my ice maker quit after the water was turned off?
Three usual suspects: the branch valve was only partly reopened, air got trapped so each fill comes out weak and spitting, or the filter was bumped loose. Let the appliance cycle overnight to push the air through. No ice by morning means the inlet valve or tubing wants a professional look.
Bringing the ice back on your own
None of this needs tools beyond your hands. Quit as soon as water starts reaching the mold.
-
Follow the line from the wall
Find where the thin supply tube leaves the wall or the sink cabinet. Turn the little valve fully open, then trace the tube to the appliance for kinks or a crushed section.
-
Bleed out the air
Where the unit has a dispenser, fill a jug or two until the flow stops spitting. Models without one purge air through the ice maker itself over several fill cycles.
-
Reseat the filter
Remove and reinstall the filter so it clicks or turns fully home. Sitting even slightly proud, it can shut flow off entirely.
-
Discard the first batches
Throw out the first few harvests after water work. Expect undersized, milky or pipe-flavored cubes while the line clears.
-
Give it overnight
An ice maker works in cycles. If water now reaches it, wait until the next morning before deciding whether it is still faulty.
Why plumbing work upsets an ice maker
No part of a refrigerator leans on the plumbing more than its icemaker. An electric valve snaps open briefly, lets in just enough water to fill the mold, and closes. If the pressure behind it drops, if air rides into the line, or if debris from the work travels down the tube, that small fill turns into a sputter, a trickle or nothing at all.
Houses on this stretch of the Westside see a lot of plumbing work: kitchen remodels, repiping in older homes, new pressure regulators on hillside lots where street pressure can be strong. Each of those jobs drains and refills the lines. Air pockets usually clear on their own within a few cycles, and debris often stops at the filter. But a burst of sediment or a pressure spike can stick an inlet valve open or closed, and no amount of jiggling at home will undo that.
Water that came back on after the work can also show a problem that was waiting. An inlet valve already near the end can fail after sitting dry; a tube that was brittle may crack when the cabinet is pushed back. If ice production does not return after the steps above, or puddles show up near the cabinet, book the repair.
What the ice tells you
- No ice at all, mold stays empty
- Supply valve closed, filter not seated, or the inlet valve not opening Repair page
- Thin, hollow or half-formed cubes
- Low pressure or air in the line, giving a short fill
- Cubes welded together into one lump
- A valve that drips after it should close, or a fill that overflows the mold
- Cloudy, odd-tasting ice in the first batches
- Fresh pipe and a new filter flushing through; usually clears after a few harvests
- Puddle on the floor beneath the toe kick
- A loose fitting or cracked tube from the plumbing work; close the supply valve and call
- A hum or buzz behind the cabinet when it tries to fill
- The fill valve straining against weak supply
Ice maker myths after a plumbing job
-
For
If the faucet runs fine, the ice maker has water too.ReadThe refrigerator has its own small valve and line. The kitchen tap tells you nothing about whether that branch was reopened.
-
For
Banging on the mold will get it going again.ReadIt can crack plastic parts or bend the stop arm. If the mold is frozen solid, the fill or valve is the real problem.
-
For
A new filter always means better ice right away.ReadFresh cartridges want flushing, and one that is not locked in can starve the line altogether.
What is the way to purge air from a fridge water line?
Units with a dispenser: draw water into a jug until it runs smooth, with no spitting or coughing. Units without: the icemaker pushes the air out as it cycles, so give it a night and bin the earliest cubes it makes.
Your job or ours
Usually a home fix
- Supply valve left part-closed after the work
- Air in the line, cubes improving with each cycle
- Filter slightly out of place
- Ice maker switch or setting turned off by accident
Time to call
- No water reaches the mold after the valve is open and a night has passed
- A hum behind the cabinet with the mold still dry
- Water leaking under or behind the unit
- Ice block forming because the valve does not shut
- The ice maker in a standalone undercounter unit stays silent
ReadingIf the steps above bring water back, you are done. If not, the inlet valve or line needs a technician.
Ice maker questions
- Can my plumber fix the ice maker while they are here?
- They own the house side: shutoffs, tubing and pressure. Everything past the connection, from the inlet valve to the icemaker and the Sub-Zero controls, belongs to an appliance technician.
- Could one visit cover the undercounter ice unit and the fridge?
- It could. We bill $89 for the trip rather than per appliance, so the undercounter unit and the fridge can share it; any repair is quoted after we look.
- Is there anything to do before guests arrive?
- Give the icemaker a head start of several days before a party, and keep a bag from the store in reserve. The holiday prep guide has more, and ice makers in Topanga covers the canyon side. Visits here are explained on the Pacific Palisades page.
Calls taken 24/7
Still no ice after the plumber's visit?
Tell us what work was done and what the ice maker does now. The $89 trip takes in all your Sub-Zero units, and repairs wait for your okay on price.
$89 covers the trip, not each appliance; it is then knocked off the invoice when you green-light the repair.